Maxtech PU1611 6Mpa High Bonding PU Bus Windshield Adhesive
∎Description
●PU1611 is one-component polyurethane adhesive with very good tensile strength and elasticity, primerless, can be used for the Automotive and bus industry.
Suitable for adhesion between windshield/side glass and frame of cars, buses, and special vehicles
A range of one-component polyurethane adhesives, designed for windscreen, side and rear window bonding.
∎Key Features
● High Viscosity
● No DOP
● Primerless
● Odorless
● Excellent thixotropy, non-sag properties
● Fast adhesion to substrates
● Paintable and polishable
● Excellent wear-resisting property
● Automotive OEM quality
● No oil permeated
● High bond strength designed for windshield bonding and stationary glass attachment
∎Areas of Application
●Specially used for the windshield and side glass of bus, car, railway vehicle (metro, high-speed rail), ship, spaceflight, engineering machinery vehicle, carriage and special vehicle
●For glass steel and plastic accessories (car roof, side body and car front)
●For bonding different material (such as metal, plastic, and glass) which requires high tensile strength and elasticity, the bonding can bear high mechanical deformation force
●Suitable for adhesion between windshield/side glass and frame of cars, buses, and special vehicles,to bond and seal vehicle windshields, backlights and sidelights, skylight.
 |  |
|---|---|
 |  |
 |  |
 |  |
 |  |
 |  |
∎Technical Data Table
PERPORTY VALUE
Chemical base 1-C polyurethane
Colour (Appearance) Black
Cure mechanism Moisture curing
Density (g/cm³) (GB/T 13477.2) 1.35±0.05g/cm³ approx.
Non-sag properties(GB/T 13477.6) Very good
Application temperature 5°C to 35ºC
Tack-free time1 (GB/T 13477.5) 10~40mins
Curing speed (HG/T 4363) see diagram
Shore A hardness (GB/T 531.1) 60±5 approx.
Tensile strength (GB/T 528) 6N/mm2 approx.
Elongation at break (GB/T 528 ) ≥430%
Tear propagation resistance (GB/T 529) ≥8.0N/mm
Extrudadbility (ml/min) >60
Tensile-shear strength(MPa)GB/T 7124 3.0 N/mm2 approx.
Volatile content ＜4%
Service temperature -40°C to 90ºC
Shelf life (storage below 25°C) (CQP 016-1) 9 months
∎Direction for use
Tool: Manual or pneumatic plunger caulking gun
●Cleaning: Clean and dry all surfaces by removing foreign matter and contaminants such as oil dust, grease, frost, water, dirt, old sealants and any protective coating.
●For cartridge
1.Cut nozzle to give the required angle and bead size
2.Pierce the membrane at the top of the cartridge and screw on the nozzle
3.Place the cartridge in an applicator gun and squeeze the trigger with equal strength
●For sausage
1.Clip the end of the sausage and place in barrel gun
2.Screw end cap and nozzle on to barrel gun
3.Using the trigger extrude the sealant with equal strength
●Apply Maxtech PU Sealant
For Automotive Car Windscreen/Windshield in a continuous bead using constant pressure to apply the sealant
1.Obtain a new windshield.
2.Remove the plastic surround side and top moldings correctly.
3.Cut the urethane from the outside between the glass and the pinch weld.
4.Apply a windshield primer to the frit band.
5.Apply the urethane with an electric caulking gun.
6.Lift the windshield into place.
7.Push the window down around the frame to guarantee a tight bond.
8.Allow the urethane to dry.
∎Attention of operation
Wear suitable protective clothing, gloves, and eye/face protection. After contact with skin, wash immediately with plenty of water and soap. In case of an accident or if you feel unwell, seek medical advice immediately.
This is professional auto glass glue, it is high viscosity ( thick ) , so a caulking gun will be required to apply the glue. If you using a regular ( not a professional ) caulking gun to apply the glue, please make sure to warm the glue up by using the hair dryer for 15 mins . Please do not stock it in cold place so the glue will freeze and very hard to apply.
∎Packing & Delivery
Wear suitable protective clothing, gloves, and eye/face protection. After contact with skin, wash immediately with plenty of water and soap. In case of an accident or if you feel unwell, seek medical advice immediately.
600ml Sausage Packing PU sealant
600ml Polyurethane adhesive sealant for automotive
PU sealant with tube packing
310ml tube : 20pcs per box, 2 box per carton
∎Pallet Packing :
310ml tube: One pallet can bear 56 CTNS, 2240pcs. One 20ft Can bear 10 pallets.
600ml Sausage: One pallet can bear 42 CTNS, 1680pcs. One 20ft Can bear 10 pallets.
∎Delivery time :
Normally order, the delivery time is around 10-15days.
Samples: 2-3days.
∎Transport &Storage
* Transport: Keep the sealed product away from moisture, the sun, high temperature and avoid collisions.
* Storage: Keep the sealed product in a cool, dry place.
* Storage temperature: 5~25℃. Humidity: ≤50%RH.
* Cartridge and Sausage:9 months. Pail/Drum:6 month.
